Restu Ayu Binangkit
12108216
3ka15
Building a Peer-to-Peer Network – Instructor Version
Background / Preparation
This lab focuses on the ability to connect two PC
s to create a simple peer-to-peer Ethernet LAN
between two workstations. The workstations will be directly connected to each other without using a
hub or switch. In addition to the Layer 1 physical and Layer 2 data link connections, the computers
must also be configured with the correct IP network settings, which is Layer 3, so that they can
communicate. A basic Category 5/5e UTP crossover cable is all that is needed. A crossover cable is
the same type that would be used as backbone or vertical cabling to connect switches together.
Connecting the PCs in this manner can be very useful for transferring files at high speed and for
troubleshooting interconnecting devices between PCs. If the two PCs can be connected with a single
cable and are able to communicate, then any networking problems are not with the PCs themselves.
Start this lab with the equipment turned off and with cabling disconnected. Work in tea
ms of two with
one person per PC. The following resources will be required:
• Two workstations with an Ethernet 10/100 NIC installed
• Several Ethernet cables, which are both straight-through and crossover, to choose from for
connecting the two workstations
Step 1 Identify the proper Ethernet cable and connect the two PCs
a. The connection between the two PCs will be accomplished using a Category 5 or 5e crossover
cable. Locate a cable that is long enough to reach from one PC to the other, and attach one end
to the NIC in each of the PCs. Be sure to examine the cable ends carefully and select only a
crossover cable.
b. What kind of cable is required to connect from NIC to NIC? Crossover
c. What is the category rating of the cable? Category 5 or 5e
d. What is the AWG wire size designation of the cable? 24 AWG
Step 2 Verify the physical connection
a. Plug in and turn on the computers. To verify the computer connections, insure that the link lights
on both NICs are lit. Are both link lights lit? They should be otherwise troubleshoot.
Step 3 Access the IP settings window
Note: Be sure to write down the existing IP settings, so that they can be restored at the end
of the lab. These include IP address, subnet mask, default gateway, and DNS servers. If the
workstation is a DHCP client, it is not necessary to record this information.
Windows 95 / 98 / Me/ users should do the following:
• Click on Start > Settings > Control Panel and then click the Network icon.
• Select the TCP/IP protocol icon that is associated with the NIC in this PC and click on
Properties.
• Click on the IP Address tab and the Gateway tab.
Windows NT / 2000 users should do the following:
• Click on Start > Settings > Control Panel and then open the Network and Dial-up
Connections folder.
• Click ad open the Local Area Connection icon.
• Select the TCP/IP protocol icon that is associated with the NIC in this PC.
• Click on Properties and click on Use the following IP address.
Windows XP users should do the following:
• Click on Start > Settings > Control Panel and then click the Network Connection icon.
• Select the Local Area Network Connection and click on Change settings of this connection.
• Select the TCP/IP protocol icon that is associated with the NIC in this PC.
• Click on Properties and click on Use the following IP address.
Windows 7 users should do the following:
• Click on Start > Control Panel > Network and Internet and then click the Network and Sharing Center.
• Select the Change Adapter Settings in the right and click the Local Area Connection Icon and click on Properties.
• Select the TCP/IP protocol icon that is associated with the NIC in this PC.
• Click on Properties and click on Use the following IP address.
Step 4 Configure TCP/IP settings for the two PCs
a. Set the IP address information for each PC according to the information in the table.
b. Note that the default gateway IP address is not required, since these computers are directly
connected. The default gateway is only required on local area networks that are connected to a
router.
Computer IP Address Subnet mask Default Gateway
PC – A 192.168.108.10 255.255.255.0 Not Required
PC – B 192.168.108.1 255.255.255.0 Not Required
Step 5 Access the Command or MS-DOS prompt
a. Use the Start menu to open the Command Prompt (MS-DOS-like) window:
Windows 95 / 98 / Me users should do the following:
Start > Programs > MS-DOS Prompt
Windows NT / 2000 users should do the following:
Start > Programs > Accessories > Command Prompt
Windows XP users should do the following:
Start > Programs > Accessories > Command Prompt
Windows 7 users should do the following:
Start >All
Programs > Accessories > Command Prompt
Step 6 Verify that the PCs can communicate
a. Test connectivity from one PC to the other by pinging the IP address of the opposite computer.
Use the following command at the command prompt.
C:>ping 192.168.108.1 (or 192.168.108.10)
b. Look for results similar to those shown below. If not, check the PC connections and TCP/IP
settings for both PCs. What was the ping result?
Results could possibly be: Sent=4 Received=3 Lost=1 (this is due to ARP)
Any other results probably indicate an error
Step 7 Confirm the TCP/IP network settings
Windows 95 / 98 / Me users should do the following:
a. Type the winipcfg command from the MS-DOS Prompt. Record the results:
Answers will vary depending on if Computer A or B is used.
Examples for Computer A
IP Address: 192.168.1.1
Subnet Mask: 255.255.255.0
Default Gateway:
Windows NT / 2000 / XP users should do the following:
b. Type the ipconfig command from the Command Prompt. Record the results:
Answers will vary depending on if Computer A or B is used.
Examples for Computer B
IP Address: 192.168.1.2
Subnet Mask: 255.255.255.0
Default Gateway:
Step 8 Restore the PCs to their original IP settings, disconnect the equipment, and store the cables
0 komentar:
Posting Komentar